Care and Maintenance


Protecting your investment is simple… 

 

CLEANING
Natural Stone and Quartz Countertops:
Polished Finish

For daily cleaning use mild dish soap like Ivory®, warm water and a soft clean cloth. You can also use any water based spray cleaner such as clear vinegar formula Windex® or Natural Stone Cleaner 409® (as recommended by the Marble Institute of America).

If a film, smudges, or streaks develop, use vinegar diluted with water (1 part vinegar to 3 parts water) and a soft clean cloth to remove it.

Natural Stone and Quartz Countertops:
Honed or Leather Finish

For daily cleaning of honed or leather finished stone or quartz products, use Countertop Magic® or mild dish soap with warm water and a soft clean cloth.

All of the cleaners mentioned above can be purchased at most hardware stores.

 

SEALING
Quartz Products

Silestone® (excluding Silestone® Leather series) and quartz surfaces do not require sealing.

Natural Stone (excluding Soapstone)
Your countertops have been sealed prior to installation.  Some stones will only need sealing every few years depending on the stone’s porosity and your daily use of the countertops.  To determine if your countertop needs resealing, perform a “water test”.  Learn how in the “Additional Information” section.  

Few granite and most marble, limestone, and travertine require an immediate application or multiple applications of sealer by the homeowner. The natural porosity of these stones and its use in your home requires them to have more initial sealing.

To seal your countertops, Granite-Tops offers the Stone Tech Professional Care System®.  Other stone sealers are available through various stone suppliers.

General Sealing Instructions (always follow the directions provided with your product.)

1.    Be certain your countertops are clean and free of spills.  Stains should be removed prior to sealing.  You will need 3 clean, dry, soft cloths and stone sealer.

2.    Pour a small amount of sealer, about the size of the bottom of a pop can, onto the countertop and distribute evenly with a dry cloth.  Pour more sealer onto the stone as you move onto other areas of the surface.

3.    Allow the sealer to penetrate the stone for at least 15-30 minutes.  If the sealer is quickly soaked up by the stone, which is common with marble, limestone, travertine, and onyx, repeat step 2.

4.    Take another dry cloth and wipe the excess sealer off while it is still wet.  If the sealer is already dry, apply a bit more sealer and wipe it off.  This will remove any residue.

5.    Once all excess sealer is removed, use a clean dry cloth for a final wipe down.

 

ADDITIONAL INFORMATION
     Sealer penetrates the stone, buying you time to wipe spills up.  Sealer is not a lacquer type coating; therefore spills should be wiped up in a timely manner.  Spills left over a period of time could seep into the stone and cause staining.

     If you are uncertain if your stone needs to be resealed, perform a simple “water test”.  Place some water onto your stone.  If within 15-20 minutes the water begins to absorb into the stone, it is time to reseal.  Wait for the water spot to evaporate before resealing.

     It is extremely difficult to chip your countertop.  In the event you get chip save the pieces, it can be repaired by a stone technician.  

     Even though it is extremely difficult to scratch granite and quartz surfaces, the use of a cutting board is recommended.

     Granite does NOT harbor bacteria or mold.  Tests conducted by the Hospitality Institute using e-coli contaminates show granite is second only to stainless steel in bacteria resistance.

     Stains can be removed.  Depending on the nature of the stain the most common method is a poultice of peroxide and cornstarch.  This paste applied to the area and allowed to dry will pull the stain from the stone.  Occasionally more than one application is required.  For more information on stain removal please see The Marble Institue of America 

     Natural pits or fissures in the stone do not have anything to do with how porous it may or may not be.

     Do Not use plumber’s putty or any oil based adhesives on your tops.  

     Do Not use Scotch-Brite®, scouring or steel wool pads, or any acid based cleaner on your countertops.

     Quartz is more susceptible to scorching or cracking from high heat items.  For added protection use a trivet or cutting board.

     Marble, Limestone, Travertine, and Onyx are prone to etching.  (Slate and most granites are acid resistant.)  When acid comes into contact with a stone surface, a chemical reaction takes place that may cause etching.  Sealing will give you time to wipe up spills but can not stop the chemical reaction.  Many household foods and cosmetics contain acids that can degrade a stone’s surface.  Some acidic foods are:  juice, coffee, wine, soft drinks, tomato based products, and lemons.  Do not leave these items resting on your countertops for any length of time.

     Soapstone requires multiple applications of mineral oil (found at any local drug store) over the years.  This will darken the color and assist in covering scratches.  No not use sealer on Soapstone countertops.

     Granite-Tops recommends Bullet Proof® sealer by Stone Tech® for stones that are naturally more porous such as limestone.

Please call for assistance.
866-685-3005

 

Classic Marble Restoration

If you have a stone surface that needs refinished, Classic Marble Restoration can help.

Services include grinding, honing and polishing of marble, granite, limestone and travertine floors, countertops and walls.  Full restoration to light powder polishing of all stone types.

Restoring the "Classic" look for your natural stone. 
www.classicmarblerestore.com